HULKWHEELS Gravel Cyclocross Disc Brake Carbon Fiber Rim UNI. rims 700C 45mm rim depth 21mm inner width ultralight rims
·ERD:558.5mm (not including nipple head dimension)
·Spoke Hole Angle±8°
·Spoke Tension:100 ~110kgf (radial) /115 ~130kgf (disc) front, 120~130kgf rear
·Tyre Pressure:130psi recommended max
After two years of continuous experimentation on lighter carbon fiber materials and the research and development of resins by the yuan an bike team, a set of optimal material ratios was finally reached.This is between T800 and T1000 of Toray..this is the composition table of the special materials used in T800, T1000 and UNI.you can see its tensile strength, the tensile modulus should be more balanced.
In all the test values, the strengths of UNI are better than those of rims made of ordinary materials.
*All test data are from Yuan'an laboratory
1. Lateral Stiffness
Lateral stiffness in a rim speaks to the level of movement from side to side. Laterally stiff rims feel more responsive during powerful accelerations like sprinting,Power transfer value is more efficient. a direct power transfer. Also, steering and handling feel sharper.
Under the max load of 50kgf, the UNI 45-03 deforms 9.07mm, with an increase of 22% in lateral stiffness compared to a same-deep 45-01 rim (11.65mm deformation).
2. positive Stiffness
The positive Stiffness indicates the range of weight that the rim can bear. Under different tire pressures and different rider weight conditions, any slight deformation of the rim directly affects the rolling coefficient of the rim and tire. Under the premise of ensuring the maximum load-bearing capacity of 130kg, riding through any road conditions can ensure that the rim is intact and rolls well.
Under the max load 300kgf,the UNI 45-03 deforms 8.2mm.with an increase of 10% in positive Stiffness compared to a same-deep 45-01 rim(9.06mm deformation)
2. Spoke hole tension
The best spoke tension value is to ensure excellent rigidity requirements without excessive vibration. The test values of UNI 45-03 and same-deep 45-01 are very close, both are 340kgf. Therefore, it can be proved that the lighter spoke hole wall thickness design will not reduce the tension of the spoke hole.
2. Impact Resistance
Under UCI's test standards, we conducted 24 impact tests, one impact at the corresponding position of each spoke hole, and the rim was still intact after 24 impacts.
Lighter and stronger wheels are always our pursuit. Different rim shapes determine the aerodynamic performance of the wheels. More importantly, the competition wheels are focused on the most basic things. Power transmission and low loss performance depend on the rigidity and lightweight of the rim. Of course, hubs and spokes are also crucial factors.
The lighter, more rigid wheels can accurately control the angle of entry when cornering at high speeds, and the wheels can react quickly when sprinting to help you win.
These are the original purposes of our research and development of UNI.
For the UNI series wheels, 30 layers of carbon cloth are used to supplement the strength requirements at the main force position of each spoke hole. In the redundant position between the left and right spoke holes, we only use 15 layers of carbon cloth for reduction. Re-optimize processing. It not only guarantees the tension requirement of the spoke holes but also reduces the excess weight.
UNI's wider design, the inner width reaches 21mm, and the tire can use 700*25C~700*43C. It can meet more riding needs.
The left and right angles of each hole inside the spoke holes can reach 8.2°, and the angle of the upper and lower spoke holes can reach 3.4°, which can meet the angular demands of more large flange hubs of road disc brakes.
Not only that, on the premise of ensuring the tension of the spoke holes, we also need to consider the side rigidity of the rim. High-power input requires not only high spoke tension transmission, but also sufficient rigidity of the rim to be transmitted to the tire to roll. Therefore, we added 2.5cm wide T800 carbon fiber on the side of the spoke hole. Therefore, the side rigidity has been increased by 30%, which has a better transmission value than ordinary weight wheels.
Therefore, the UNI series is the lighter, stronger and more perfect rim you need.
CHA/Customized spoke hole angle
All spoke hole angles must be customized according to the geometric angle of the hub.all drilled holes are inspected to ensure they are free of burrs.You can request a customized drilling pattern if you have a unique wheel build.
TRD/Tubeless R angle design
All yuan an bike are tubeless compatible.We design a R angle,The rounded edge makes tire installation easier and offers increased support during hard cornering with a softer edge and larger surface area.
LMS/lighter materials improve the strength
We use lighter materials and make full use of the combination of T800 and T1000 to improve the strength.
SIW/smooth Inside Wall
We use a specific, thinner, high-pressure air bladders to control the inner wall smoothness, and the inner wall air bladders can be extracted clean at one time, without residue, not only effectively improve the tightness of the carbon fiber yarn, but also allow the spoke cap to be more tightly integrated with the spoke hole.
OPT/one piece technology
Compared to the technology of 3 piece, our one piece tech is more technically difficult and takes longer to produce, but the rigidity of the rim is at least 7% higher.
BLT/Bead Lock technology
The bump on the rim bed helps to create a buffer during tire inflation, making the mounting process easier. When the tire is mounted, the raised portion reinforces the tire bead, making it harder to "burp" or fall back into the drop channel.
URT/Unique resin technology
To improve the stability of the wheel, we think the material control is the root.So we import carbon fiber raw yarn from Toray, Japan, and mix with the high-temperature-resistant resin which researched and developed by our own, weaving them to be prepreg .So, from the source we firmly control the quality.
EPT/Environmental protection technology demoulding
Compared with many oil-based mold release agents, we use a neutral mold release agent imported from Germany, because we use labeled "NAK80 steel", which is a very high-strength abrasive tool, compared to ordinary P40 For steel, NAK80 has a firmer surface and a smoother rim surface.
HBW/Hand bulit wheel
From prototype to production, every wheel gets assembled by hand. There is no substitute for the experience and meticulous attention to detail that a human being brings to the craft of wheel building.